Telecom & Data

manufacturing delivery11 products

requirements · 11

What this sector arrives with

copynot yet written

A 48 VDC plant that has to survive a bad grid without a site visit — redundancy, low-voltage disconnect, remote alarms — or a wide-input stabiliser for equipment on a network that swings outside tolerance. Lead with the redundancy and monitoring architecture.

categories serving this industry · 05counts are products serving this industry

Voltage Regulation & Power Conditioning

Servo, IGBT static and relay-controlled AC voltage regulators, plus harmonic and surge filtering.

Battery Chargers & DC Systems

Grid-station, telecom, industrial and specialist battery chargers with DC distribution and battery banks.

Step-down, isolation, rectifier-duty, control and waterproof transformers wound to order in pure copper.

DC Power Supplies & Rectifiers

Thyristor-controlled plating and process rectifiers from a few amps to 20,000 A, and variable laboratory-grade DC supplies.

Panels, Distribution & Controls

AC and DC distribution boards, SCR heat control, PFI, ATS, motor starters and protection relays.

Products for this industry · 11ratings are standard builds · pricing by enquiry

Automatic Plating Rectifier

Thyristor-controlled, closed-loop DC supply for electroplating lines — low-voltage, very high current, with optional periodic reverse.

0–60 VDC · 100–20,000 A

Telecom Battery Charger 48 VDC (1+1 Redundant)

Dual-module 48 VDC power system built to telecom specifications, with N+1 redundancy and load sharing from 30 A to 200 A.

1–415 VAC · 30–200 A

Floating Battery Charger 24 VDC

Compact 24 VDC float charger, 20-70 A, for communications, signalling and vehicle-battery duty.

220 VAC · 20–70 A

Battery Banks, Stands & Fuse Boxes

Matched battery banks with stands, inter-cell links and fused isolation, supplied and commissioned with the charger.

110 VDC 400 Ah with battery fuse box

Servo-Controlled Automatic Voltage Regulator

Motorised-variac AVR from 500 VA to 300 kVA holding output within ±1-2% against a ±25% input swing, with no added waveform distortion.

380 VAC ±1% to ±2%, 3-phase; 220 VAC ±1-3%, 1-phase

IGBT-Controlled Static AVR

Transformerless-tap static regulator, 2-100 kVA, correcting to ±1% in milliseconds with no moving parts.

2-15 kVA single-phase; 5-100 kVA three-phase

Relay-Controlled Voltage Stabiliser

Economical stepped-tap stabiliser, 300 VA to 8 kVA, with a very wide 90-280 VAC input window for weak distribution networks.

220 VAC regulated

Harmonic Filter

Passive filter delivering a clean sine wave to sensitive electronic loads on distorted supplies.

Step-Down Distribution Transformer

Dry-type LT step-down transformers, 5-300 kVA, typically 380-415 VAC 3-phase to 208/120 VAC, wound in pure copper.

5 kVA to 300 kVA (30-150 kW commonly supplied)

Isolation Transformer

1:1 galvanic isolation transformers, 5-300 kVA at 415/415 VAC 3-phase, for solar, UPS and sensitive-load installations.

5 kVA to 300 kVA (10-100 kVA commonly supplied)

DC Distribution Board (DCDB)

Compartmentalised DC distribution boards with per-circuit MCBs, monitoring and earth-fault detection, up to 20 outgoing ways.

24 / 48 / 110 / 220 VDC

not listed

A rating outside these builds

Send the input supply, required output, enclosure rating and site ambient. We quote against the same platform as the listed builds.